Just how to Replace a Bath Tub ( Guide).
Just how to Replace a Bath Tub ( Guide).
Blog Article
The article author is making a number of good points on the subject of A Step-by-Step Guide to Installing a Bathtub overall in this content followed below.
Installing a tub isn't exactly rocket science, yet it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently easily accessible, the task can move easily; if you have to open up a wall to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will need an assistant to leave the old bathtub and embeded in the new one. Make certain you have actually qualified yourself for the work and fit trying it. Instead of employing a service provider to take over a halfway-completed job, it is much better to take into consideration employing one before you start. Opportunities are you might require a professional plumber to make tube connections.
This post will certainly help you install a new tub in your washroom if you have already purchased a brand-new bathtub and also don't need to change the plan of your previous water system pipelines.
Your devices and also product checklist ought to make up the following:
Preparing for the Installation
First of all, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the versatile tap adapters to the bottom of both taps utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its final placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be rather troublesome due to the limited accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipelines. When the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the bath tub up until the level checks out level.
To mount taps, fit all-time low of the furthest flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Fill the tub as well as also examine the overflow outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and securing around the bath tub should wait until the tub has been made use of at least when as this will settle it right into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Safeguard the tap in place with the producer supplied backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap ports. The previous kind should be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split an inflexible seal, creating the water to penetrate the wall surface in between the bath and the tiling, leading to complications with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also can securing voids as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealer can fracture rather very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is a good idea to fit the tiles using water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our piece about How to Install a Bathtub Yourself. Thanks a lot for spending some time to read our content. Enjoyed our blog entry? Please share it. Let someone else find it. Thank-you for your time invested reading it.
Schedule An Appointment Report this page